Pay in installments of $20.00 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 17 - Jul 22
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Rule LoPro 900GPH Bilge Pump - Non-AutomaticLoPro 900GPH Bilge Pump Non Automatic The Rule LoPro 900 non automatic is a low profile Bilge Pump with a 900 gallons per hour capacity. Designed for tight spaces, the height of the pump is only 2 1 4". It features a threaded discharge nozzle to which you can attach either a straight or a 90 fitting (included). In addition, you may use the tricuspid check valve {included} on the straight fitting to minimize the back flow of water. The entire discharge
LoPro 900GPH Bilge Pump - Non-AutomaticThe Rule LoPro 900 non-automatic is a low profile Bilge Pump with a 900 gallons per hour capacity. Designed for tight spaces, the height of the pump is only 2-1/4".
It features a threaded discharge nozzle to which you can attach either a straight or a 90° fitting (included). In addition, you may use the tricuspid check valve {included} on the straight fitting to minimize the back flow of water. The entire discharge body swivels up to 180° for ease of installation. The hose attached can also swivel 360° to route the hose perfectly.
Features:
- 900 GPH Low Profile Bilge Pump
- Fits into hard to reach places
- Non-automatic, requires float and or panel switch to automate
- Threaded discharge ports with mulitiple fittings available
- Features a tricuspid check valve to minimize back flow of water
WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
Manufacturer : Rule
Manufacturer Part No : LP900D
UPC : 042237114365
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.0 ★★★★★
Based on 21 reviews
Sort
Product Reviews
★★★★★ 5
Good
Configuration: 4-Stroke, Size: 1 GA, Case of 3
Good
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 15, 2026
★★★★★ 4
Oily situation lol
Configuration: 4-Stroke, Size: 1 GA
Honestly how do you write a review of this product? I would have to run tests for years on multiple oils on various engines to do so. The value was good however and shipping was great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 31, 2025
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025