Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 12 - Jul 17
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Power Conditioner, Voltage Regulator, & Battery Backup UPS For SCIEX QTRAP 6500+This system is designed to provide voltage regulation, surge suppression, and automatic emergency backup power specifically for the SCIEX QTRAP 6500+ System. Software Loaded For Specific Instrument Operation The UPS is loaded with software settings that limit the voltage fluctuations to within the range specified within the instrument site preparation guide. Hardware Configuration For Specific Instrument Operation The UPS internal bypass wire is
This system is designed to provide voltage regulation, surge suppression, and automatic emergency backup power specifically for the SCIEX QTRAP 6500+ System.
Software Loaded For Specific Instrument Operation - The UPS is loaded with software settings that limit the voltage fluctuations to within the range specified within the instrument site preparation guide.
Hardware Configuration For Specific Instrument Operation - The UPS internal bypass wire is removed which prevents voltages outside the acceptable operating range specified in the site preparation guide of the instrument to be passed through to the instrument.
-
Cuts Utility/Electric Costs compared to other battery backup UPS systems.
-
Slashes Setup/Installation Costs by requiring only a single receptacle for the UPS to be plugged into for power. If you don't already have the required receptacle, it can be installed by an electrician in advance of receiving the UPS and typically costs a fraction of the cost that it would cost to normally hardwire the UPS into an electrical panel.
-
Reduces Setup Time as the system arrives on a mini pallet with ramp included, rolls off the pallet, plugs into your wall receptacle, has a single switch/breaker on the back, and an ON button on the front LCD. The pre-installed dual voltage output PDU (power distribution unit) has all of the most used receptacles in North America so equipment can simply be plugged in. Unpacking, setup, and power up can be done within 5-10 minutes with only a Phillips screwdriver to unscrew the pallet blocks.
-
Eliminates Down Time as short duration power outages, voltage inconsistencies, surges, and other power issues are isolated away from any equipment you attach to the output receptacles.
-
Prolongs Equipment Life as built in circuit protection and voltage regulation ensure only the correct operating voltage is provided to the instrument at all times. Our factory configures this variation of the battery backup UPS in power conditioning mode so the unit will NOT ever switch to bypass mode which would potentially expose the attached equipment to the power problems and improper voltages.
-
Multiple Device Support as up to 10,000 VA of power consumption can be handled by the UPS. The output PDU has multiple receptacles and 2 simultaneous voltage outputs that match each receptacle type. Need less power? Use our 6KVA model.
- Plug And Play Functionality, rolls off the pallet ready to plug in and turn on.
- INPUT: NEMA 6-50P (Plug)
- 208, 220, 230, or 240 Volts Single Phase, 50 Amp Breaker
- OUTPUT:
- 8x NEMA 5-15/20R (Receptacles, 120 Volts)
*Fits Either NEMA 5-15P (Plug) Or NEMA 5-20P (Plug) - 1x NEMA L5-30R (Receptacle, Twist Lock, 120 Volts)
*Fits NEMA L5-30P (Plug, Twist Lock) - 2x NEMA L6-15R (Receptacle, Twist Lock, 240 Volts)
*Fits NEMA L6-15P (Plug, Twist Lock) - 1x NEMA L6-20R (Receptacle, Twist Lock, 240 Volts)
*Fits NEMA L6-20P (Plug, Twist Lock) - 4x NEMA 6-15/20R (Receptacles, 240 Volts)
*Fits Either NEMA 6-15P (Plug) Or NEMA 6-20P (Plug) - 1x NEMA L6-30R (Receptacle, Twist Lock, 240 Volts)
*Fits NEMA L6-30P (Plug, Twist Lock)
User Guides:
-Battery Backup Power 6KVA-10KVA 1.0 PF Advanced Digital Tower UPS User Guide
-Battery Backup Power SNMP Card Full User Guide.pdf
Spec Sheet/Cut Sheet:
-BBP 4.5-10KVA 1.0 PF Advanced Digital Tower Specification Sheet.pdf
Complete 5 Tier Power Protection System – Surge Protection, Real Time Power Conditioning With Voltage Regulation, Heavy Duty Isolation Transformer, Pure Sine Wave Output, & Always On Double Conversion Backup Power Technology.
Extreme Energy Savings - Saves up to $3,153.60 per year over older model 10 KVA UPS systems in annual electricity costs due to energy efficiency enhancements.
Multiple Backup Time Options:
| Model Number: | Description (Under Battery Options Drop Down): | Approximate Backup Time At Full Load: |
| BBP-ADV-10K-650P-120240PDU-QTRAP-6500PLUS | UPS With Internal Batteries Only (20 Batteries, 12 Volts, 9 Amp Hours Each) | 11 Minutes |
| BBP-ADV-10K-650P-120240PDU-QTRAP-6500PLUS-WEBPWC | UPS Plus 1 Extra External Battery Pack (80 Batteries, 12 Volts, 9 Amp Hours Each) | 46 Minutes |
| BBP-ADV-10K-650P-120240PDU-QTRAP-6500PLUS-W2EBPWC | UPS Plus 2 Extra External Battery Packs (140 Batteries, 12 Volts, 9 Amp Hours Each) | 1 Hour 21 Minutes |
| BBP-ADV-10K-650P-120240PDU-QTRAP-6500PLUS-W3EBPWC | UPS Plus 3 Extra External Battery Packs (200 Batteries, 12 Volts, 9 Amp Hours Each) | 1 Hour 56 Minutes |
| BBP-ADV-10K-650P-120240PDU-QTRAP-6500PLUS-W4EBPWC | UPS Plus 4 Extra External Battery Packs (260 Batteries, 12 Volts, 9 Amp Hours Each) | 2 Hours 31 Minutes |
| BBP-ADV-10K-650P-120240PDU-QTRAP-6500PLUS-W5EBPWC | UPS Plus 5 Extra External Battery Packs (320 Batteries, 12 Volts, 9 Amp Hours Each) | 3 Hours 6 Minutes |
- 10000 VA (10 kVA) / 10,000 Watt (10 kW)
- N+1 And Parallel Operation Up To 40 kVA (4 Units In Series)
- Energy Efficient/High Efficiency UPS Mode
- LCD Status Measurements Include Voltage, Frequency, Load Level, Battery Level, Output Current, and Estimated Remaining Backup Time
- Tower With Casters
- Pure Sine Wave Clean Output To Operate And Maximize The Life Of Even The Most Sensitive Electronics
- Online (Double Conversion) - Highest Level Of Protection Available - Battery Power Always Engaged, No Switching Delay (Phase Locked To Input Power Source)
- Wide Frequency Input Range (44-66 Hz Auto Sensing) Allows For Generator Power To Be Used As A Primary Or Secondary Input Power Source (Using Automatic Transfer Switch Before UPS)
- Constant Voltage Regulation (±1%)
- Constant Frequency Regulation (±1 or ±3% Selectable)
- Factory Warranty: 3 Years On Electronics And 1 Year Warranty On Batteries
- Optional Extended Warranty: 5 Years On Electronics And 1 Year Warranty On Batteries
- Digital Signal Processing (DSP) Allows For Greater Reliability Over Older UPS Designs And Superior Electric Noise Filtration
- >0.99 Input Power Factor / 0.9 Output Power Factor (Line Mode) / High Efficiency Mode For Superior Efficiency And Power Savings
- UPS Weight (Excluding Optional External Battery Packs): 294 lbs.
- Dimensions (Inches): 11.4 X 26 X 28 (W x H x D)
- Operating Temperature: 32°-104° F
- Operating Humidity: 20%~95%, Non-Condensing
- Operating Elevation: 3,280 Feet Without De-Rating
- Cold Start Capable (Shipped With Cold Start Disabled, Will Enable Automatically After Receiving Power For The First Time After Shipping)
- cTUVus, cULus, and FCC Certified
- Includes Software For Windows Monitoring & Configuration
Replacement Batteries:
-Leoch DJW12-9.0 (Lead Acid), Leoch LP12-9.0 (Lead Acid), Betta Batteries 6-HCNFJ-7.2 (Lead Crystal), Or Battery Backup Power BBP-LIFEPO4-HDR-12V-7.2AH (Lithium Iron Phosphate)
Do you need a PDF quote or a custom emergency backup solution? Email us at [email protected].
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 1622 reviews
Sort
Product Reviews
★★★★★ 5
All-around good chair, suitable for me at 6'6", comfortable and no issues
Pros:
The assembly is straightforward and doesn't require much strength; I would expect my mother to have no issue putting this chair together. If you're elderly or disabled, a relative or helper should have an easy and quick time of putting it together, and there is very little chance of making a mistake during assembly.
Sturdy at and slightly above the recommended weight limit. I peaked around 256 or 258lbs while using this chair, and it didn't show any signs of complaint then, and it hasn't shown signs of wear since.
Really comfortable. I'm an eight-hours-a-day user, almost without exception, and I have no complaints.
The leather holds up very well. I don't expect this to be true forever, but after approximately 1800 hours of use, there is no tear or warning sign.
It leans back super stably. That's the most important aspect for me.
It's tall enough to support my 6'6" frame. My back rests comfortably, so the odds are yours will fit, too. For the scary few who tower over me, and so you can search it easily, here's a height guide:
6'3" 6'4" 6'5" - The chair is good for your heights
6'7" - You should also be well served, unless your height is mostly in your torso.
6'8" - You're at the cusp. I think you will be comfortable in this chair, and alternatives that are built for our (mostly your) height cost so much more. I'd give it a try. I wish you luck.
6'9" 6'10" 6'11" - This is written for 6'9. For 6'10, 6'11, scale the significance of the caution. I think this chair will prove uncomfortable for you or encourage bad posture. I'd encourage you to look elsewhere.
Cons:
This is well covered in other reviews: the caps that cover up the screws on the side of the arms are poorly designed. One falls off every day or two. It's a minor inconvenience, but it's optional. You can toss the caps in the trash. The screws are not exposed. They sit deep within the plastic of the arm. Personally, I just push the covers back on when I notice they fell.
The armrests could be better for me, I think. I'm not sure exactly what my complaint is. I think they are a little too narrow for my liking, but I'm 6'6" with broad shoulders and long arms and unusual joints. The spacing seems fine for a typical user.
Notes:
I only sit leaning the chair back or sitting up straight at the edge of my seat. Some aspects of this review may not translate perfectly to locked-in-place, sitting back, upright usage.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 8, 2018
★★★★★ 5
Awesome!
Update: March 2022 - Funny reading my previous review now. All the cons I mentioned before, I literally don’t even notice at all. In fact, I like the chair I got so much I just got another in white. My boyfriend is using the old one and I needed one for my home office. And sadly, my cats did scratch up the black chair a little (the cats live outside now) but the chair has otherwise stood up to use perfectly. Other than the scratches, is basically like new. I do wish I knew of a good repair kit cause I would like to fix up the scratches. The chair is just extremely comfortable and supportive which I need even more these days for my home business. A very good purchase!!
I just received my chair 2 days after ordering it. It took me about 20 minutes to put it together which was very easy. I am sitting in it now typing this review.
Pros:
-Very attractive. I ordered the black color and it appears just as in the pictures.
-Slides smoothly over my linoleum floors.
-Seat is soft and comfortable, hopefully it will stay that way over time, but too soon to tell.
-Very easy to assemble.
-The seat is good size for the average American and seems comparable in width to the chairs I use at work.
Cons:
-The chair does not lower as much as I wanted. I like my legs at a 90 degree angle when sitting. It is close with my shoes on, but about 2 inches to high. If I had known this, I very likely would not have ordered this chair as its one of my most important features for sitting comfortably. I am 5'6”. I hope that with a little wear the cushion will compress a bit, and if not I may get a small foot stool to solve the problem.
-As others have described, this chair pretty much doesn't recline in any appreciable way even at the loosest setting. Basically to stay reclined you have to keep your legs pushing back the whole time which eliminates the point of reclining. I have read from others that over time, this loosens up. This feature is not very important to me, but may be to others.
-The seat depth is about 2 inches shorter than I would like.
Overall, I think it is a quality chair for the price assuming the above negatives aren't deal breakers for you. I will be keeping this chair since I do not spend a lot of time at my desk and the overall quality outweighs the few negatives for me.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 27, 2016
★★★★★ 5
I would buy it again
Color: White/Pewter, Color: White/Pewter
This chair is very comfortable and easy to sit in for long periods of time. The leather is soft and well stitched.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 22, 2026
★★★★★ 1
Updated after less then 3 months of owning!
I have only had the chair a few hours now so this review is of first impression and details. I usually wait to do reviews but choose to on this one.
Things I noticed that maybe important to others as information: If you are a tall person you may want to measure your height and etc. I am 5' 6" Tall 175lbs. and this chair is perfect size for me. it does have some room 20" max width from arm rest to arm rest. seat is 19" deep from back to front, Back Height from seat is 26" to top (Will be a little more height when sat on) but this being said the top of my head is just perfectly at the top of the head rest height.
Putting it together is a breeze and anyone could put this together, Everything's Labeled to fit the instructions, packaged well. Took me about 10 minutes.
Pros: Very Comfortable, Perfect size for me, Looks Great, Easy to put together if you follow the easy directions. No tools needed (Tool is included), Arm rests Height Perfect,
Cons: The Back is only held together by the arm rests, This I find very odd but possibly normal to all chairs. If you rock the chair back and forth you can feel the back flexing (This I believe to be why others have claimed the chair squeaks and makes noise while tilting back). I am going to make a bracket that will attach the back to the bottom of the Seat to keep it secure and sturdy for the long haul.
P.S update on the chair after less then 3 months of owning, although the chair is still comfortable but with a major Con. with normal daily use the fake leather on the arm rests has started to crack and peal. I will not be buying this chair again nor recommend to anyone.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 17, 2015
★★★★★ 3
I really wanted to like this chair,
it looks good, it is a nice size, and it starts out pretty comfortable. The vinyl seems pretty durable and I've not had the troubles others have noted with seams tearing or starting out faulty, mine have been near perfect. Assembly is easy, just 12 screws and you simply put them all in finger tight, then toque them down a bit at a time over about 3 passes to get them evenly tight while letting everything balance out as it goes. Much like changing a car tire. If you install one screw and tighten with all your might then move on to the next you'll have trouble with anything you try to assemble, including this chair.
Assembly is rarely a problem for me, but the issue here is the padding. I weigh less than the weight limit but I'm tall and thin and my muscular bicyclist's butt is apparently too much for this chair's cushions. At 8 months, I gave up on blankets and pillows and Amazon politely replaced my first chair with zero fuss. Two months later I got a job telecommuting and the 2nd chair has gone totally flat in only another month. I really wanted to like this chair, but the padding just doesn't last. Update: I've been using an additional pad in the seat and though I'm not fond of the look, the price is right since I already paid for the chair. A couple days ago I leaned back and hear a "pop". The back is all floppy and so I take it apart looking for the problem. I tracked the problem to a metal bracket inside the upholstery. I had to cut the vinyl to reach the problem but found the bracket is a large well engineered solid steel plate with plenty of surface area to handle the stresses and the wood is top quality plywood with no voids. Amazon did an awesome job having this chair re-engineered and specified good materials, but their assemblers didn't bother to tighten the screws. No amount of engineering can fix lousy assembly work. Amazon is clearly trying here but they're being thwarted by their supply chain left and right. To be fair, the two chairs they have sent me collectively did last enough for the price I paid so I won't be asking for another replacement.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 16, 2018