Blackmagic Design Spares - ATEM TV Studio Pro HD - PCB Main
SKU: 29721131180

Blackmagic Design Spares - ATEM TV Studio Pro HD - PCB Main

Sale price$9191.83 Regular price$10213.15
Save 10%

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 8 - Jul 13

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Blackmagic Design Spares - ATEM TV Studio Pro HD - PCB MainThe Blackmagic Design Spares ATEM Television Studio Pro HD Main PCB is the primary processing motherboard for the all in one live production switcher. While the chassis houses several smaller boards for the buttons, fader, and audio I O, the Main PCB is the central "hub" where all video switching, FPGA based effects, and system logic reside. Because the Television Studio Pro HD is a fan cooled, high density unit, the Main PCB is designed to handle

The Blackmagic Design Spares - ATEM Television Studio Pro HD - Main PCB is the primary processing motherboard for the all-in-one live production switcher. While the chassis houses several smaller boards for the buttons, fader, and audio I/O, the Main PCB is the central "hub" where all video switching, FPGA-based effects, and system logic reside.

Because the Television Studio Pro HD is a fan-cooled, high-density unit, the Main PCB is designed to handle simultaneous 1080p60 processing across 8 inputs while managing the internal hardware control panel.


Core Responsibilities

  • Video Cross-Point: Manages the physical switching between the 4 SDI and 4 HDMI inputs.

  • FPGA Processing: Drives the DVE (Digital Video Effects) engine, upstream chroma keyers, and two downstream keyers.

  • Resync & Scaling: Each input on this board features a dedicated frame re-synchronizer, allowing you to mix consumer cameras and professional broadcast sources without external genlock.

  • Multiview Generation: Processes the 8-input + Program + Preview layout for the HDMI and SDI Multiview outputs.

  • Flash Memory: Houses the non-volatile memory for the Media Pool, allowing the switcher to retain 20 RGBA graphics even after power-off.


When to Replace the Main PCB

  • Total Signal Blackout: The console powers on and the buttons light up, but there is no video output from Program, Preview, or Multiview.

  • Input "Death": Specific inputs (e.g., all 4 HDMI ports or all 4 SDI ports) stop functioning simultaneously while others work, indicating a failure in the input controller bank on the Main PCB.

  • Fan/Thermal Error: If the onboard thermal sensors fail, the switcher may refuse to boot or enter a permanent "emergency shutdown" loop.

  • Sync Issues: Frequent "glitching" or frame-tearing across all inputs that isn't resolved by firmware updates usually points to a failing clock crystal or FPGA on the motherboard.

  • Network Connectivity Failure: If the Ethernet port is physically fine but the ATEM Software Control cannot "see" the unit even after a factory reset, the network controller on the PCB has likely failed.


Technical Installation Note

Repair Level: 4 (Advanced). This is a significant mechanical undertaking.

  1. Bottom-Entry Access: You must flip the console and remove a large number of screws (roughly 20-30) to remove the bottom metal plate.

  2. Ribbon Cable Forest: The Main PCB is connected to the Button Panel PCB, the Audio I/O Board, and the T-Bar assembly via numerous delicate ribbon cables. You must map these carefully before disconnection.

  3. The Cooling System: The Main PCB is cooled by an internal fan and a copper heatsink. When swapping the board, you must ensure the heatsink is properly seated and fresh thermal paste or pads are applied to the central processing chips.

  4. Internal Power Supply: The $110\text{V}$$240\text{V}$ IEC power supply module is located near the Main PCB. DANGER: Ensure the unit has been unplugged for at least 15 minutes before touching internal components to allow the capacitors to discharge.


Diagnostic Tip: Firmware Recovery

Before assuming the Main PCB is dead, attempt a Recovery Mode update:

  1. Connect the ATEM to a computer via USB.

  2. Hold down the Set button (or Inquiry on some versions) while powering on the unit.

  3. The ATEM Setup Utility on your computer should prompt you to "Recover" or "Update" the firmware. If this fails to register the device, the Main PCB logic is almost certainly compromised.

Expert Advice: If your issue is only related to the physical buttons not responding, you likely need the Control Panel PCB, not the Main PCB. The Main PCB is only the culprit if the electronic "brain" of the switcher is failing to process video or communicate with the software.

Are you losing video signal entirely, or is the console simply failing to connect to your computer?

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 29721131180

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.5 ★★★★★
Based on 695 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
B
Verified Purchase
Brenda McMullen
Massapequa, US
★★★★★ 5
Quality
Color: Black
Fits perfectly! Great for kids who are rough on iPads. Seems indestructible
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 20, 2026
T
Verified Purchase
Tyia
Natrona Heights, US
★★★★★ 4
Good buy
Color: Purple Pink
Everything as pictured good quality and durable only thing I didn’t like is the strap isn’t adjustable.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 3, 2026
C
Verified Purchase
Cameron Whitworth
Los Angeles, US
★★★★★ 5
Good for kids
Color: Purple Pink
Perfect for my daughter’s new iPad. Very durable. Love the pink and purple color. Easy to put together.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 14, 2026
M
Verified Purchase
Meranii
Natrona Heights, US
★★★★★ 5
Perfect case for my daughter’s iPad
Color: Purple Pink
bought this case for my daughter. The fit is perfect — all the buttons and camera line up exactly and it snaps on securely. The case feels sturdy, protective, and durable but not too heavy, so she can still carry it comfortably. The stand feature is convenient. The design is also super cute — Luna loves it Overall, great quality for the price. I would definitely buy it again
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 15, 2026
G
Verified Purchase
G D
Carnegie, US
★★★★★ 5
Perfect case
Color: Purple Pink
Great protection for my IPad. I’m always dropping something. This case was pretty easy to install and has the protection over the glass front. No problem using the iPad with the cover. Cute colors and has a loop to store the pen
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 9, 2026

recommand products